TV & Home Audio Amplifier Parts & Components

1 X DC 12V 24V 100W TPA3116DA Mono Channel digital Power audio amplifier board. Output Power: 100W. Channels: Mono. size: 79 54 16MM. Chip Type: TPA3116D2.

Power amplifier chip: TDA8954TH(dual chip). Power amplifier: 2x420W. Number of channels: left and right channels.

Using LM1036 tones chip, SMD production process, Small size, stable performance. Power input increased the rectifier bridge, can be AC and DC input, when DC input don't need distinguish between positive and negative, easier to use.

DIY Kits Soft Starting Switch Power For Amplifier. DIY full kit ( PCB components) of a soft start switch for high power amplifier. 1xDIY Kits Soft Starting Switch Power For Amplifier 300-2000W. Power: 300W-2000W.

TDA7294 Mono Audio Power Amp Amplifier Board DIY Kits. 1set x TDA7294 Mono Amplifier BoardKits. Dual DC 40V 80W 20Hz-20KHz. The official line using standard circuit design, small size and mono design, easy installation.

Remote For Amplifier DC 5-12V. 1pcs x Digital display board. 10, Board size: 27 33mm. 6, Frequency Response Range: 20Hz-20KHz. 1pcs x Receiving head. And hope to see you soon.

MPN Does not apply Brand Unbranded UPC 191466390207 EAN 191466390207 ISBN 191466390207.

Chip type: TPA3116D2. Channel amount: Dual 50W. So, you need a common ground isolation board;. 1x Amplifier Board.

Reminder: Each board can serve one audio channel. For indication of two channels such as stereo, two boards are needed. We are committed to resolve all issues in a friendly and satisfactory manner.

MX50 power amp X 1 (include 2 assembled boards). -Installation: High-power tube to be insulated and radiators,installing insulation film. -Output Power: 100W8R( -42V). low-noise audio tubes BC546B,BC556B and audio-specific driver tube 2SB649,2SD669 As a pre-promote.

XR1075 2 Channel BBE Tone Board. 1pcs x XR1075 Tone Board. And hope to see you soon. Board Size: 100mm x 33mm.

Product Model: LM1036n. with a loudness function, the effect is very good. This is not a finished board. this is KIT only DIY Kit. This is a Kit . and can extend to the plate with an ordinary wire install, without causing noise increases.

1 x Fully completed and tested LT3045 PCB. LT3045 x2 : IC, Low Noise Power Solution, Linear Technology – United States. • Ultralow RMS Noise: <0.8µVRMS (10Hz to 100kHz). • Ultralow Spot Noise: 2nV/√Hz at 10kHz.

1× AK7115 Assembled Board. ·Dedicated VFD display, Resolution 71 X 15. ·Software AGC Custom output curve,In order to ensure that the input signal inlarge range of output effect is ideal. ·Unique spectrum smoothing algorithm to make the best balance between real and visual beauty.

Bluetooth 4.2 Amplifier Audio Board 5W 2 Stereo Amplificador AUX Wireless Bluetooth Receiving Modification DC3.7-5V. 1 XBluetooth 4.2 Amplifier Audio Board 5W 2 Stereo Amplificador AUX Wireless Bluetooth Receiving Modification DC3.7-5V.

Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. 1.6mm thick sheet using double-sided PCB, 2.0 oz copper thickness, HASL whole process to ensure that the size of the current through the good performance.

2 X 300W Class D Audio Amplifier Board Compact - TAS5630. It not only inherits its original performance basis including support for dual channel simultaneous outputting, low THD N, high SNR, powering up with music signal input.

This kit can built 5V 9V 12V 15V 18V 24V 30V several kinds output votlage.Juse need change the "VA" and "RA". The schematic diagram is open source. The circuit design, as well as the printed circuit board layout are the work of AMB with participation from the DIY community.

Output Power: 50Wx2. 1 PCS x Power Amplifier Board. Channels: Two Channel Stereo. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Otherwise deal is final.

1 x TPA3116 100W 100W Digital Power Amplifier Board. Make sure the correct wiring before connecting the amplifier board;. Power on the amplifier board after confirming the wiring. Output channel: Left channel & Right channel.

100% Brand new and high qualityThis version can be controlled 500W amplifier, each channel using a relay control.Power: AC 12-24VStart delay 1S closed, no need to use 3S delay. DC monitoring and protection, real-time protection speaker;Disconnect the speaker off instantly.UPC1237 best performance as core devices, with power-on delay and DC protection, power anti-shock functionUse OMRIN original high-current relay as the core of the device is not afraid of contact ignition and oxidationUsing 7812 as a regulator, wide supply range, up to any range AC12V to AC24V circuit is simple and reliable. Produced very easily, no need debuggingimported relay, silver contacts.Precision CNC double-sided circuit board tin small size, easy installedPCB size:7cm × 57mm/2.76*2.

6 (14) is a low-pass filter pin end, 7 (13) feet high pass filter end. 1 x AC/DC 12V R1075 Tone Board BBE Digital Audio Processor Actuator Pre Amplifier. Digital Microscope. If you are satisfied with our service, pls.

Select category: Bluetooth Mod. Wireless Module. Active speaker with bluetooth functon. Among these, the reserved port is connected with a 100 ohm resistor in series. After the Bluetooth connected, it is flashing slowly.

Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing.

Signal Selector Relay Module DIY Kits. 2pcs x Capacitance. 4pcs x Rectifier. Audio Switching Board 4 Select 1 Audio Input. 4 select 1 audio input select board, used with audio input selection, 4 channel input, 1 channel output.

The new imported TDA7294 chip; KB level PCB board, all components have been marked in the screen printing plate, easy to install DIY friends. 1x TDA7294 Amplifier Kits. To the right of mono output.

Bluetooth 4.2 Amplifier Audio Board 5W 2 Stereo Amplificador AUX Wireless Bluetooth Receiving Modification DC3.7-5V. 1 XBluetooth 4.2 Amplifier Audio Board 5W 2 Stereo Amplificador AUX Wireless Bluetooth Receiving Modification DC3.7-5V.

Mute delay boot,shutdown speed off. 1x Protection Circuit Board.

Active speaker with bluetooth functon. Among these, the reserved port is connected with a 100 ohm resistor in series. After the Bluetooth connected, it is flashing slowly. 1 x Bluetooth Module. Due to the difference between different monitors, the picture may not reflect the actual color of the item.

2, selected NE5532, welded IC holder can always replace the amplifier, experience different effects to enhance playability. 4, PCB board design simple and beautiful, reasonable wiring, making the board has a very high signal to noise ratio, strong anti-interference ability.

Chip: CM6631A. About driver installation: First, extract the compressed file, Before open the installer ,do not opening the installer CM6631A interface card connected to the computer, then follow the prompts to connect!

1 x New Silver HIFI 2.0 Stereo Output Digital Power Amplifier TPA3116 50Wx2. Adopt the German Weimaraner MKP10 as input, richer overtones. Power range :8-25V. 12V ------- 8 Ohm speaker / 12W (left channel) 12W (right channel), 4 ohm speaker / 20W (left channel) 20W (left channel).

1xDC 12V 24V 120W 2 TPA3116 Dual Channel digital Power audio amplifier board. DC24V, 2 120W. Channel: Dual channel stereo. Onboard front-facing IC to improve the input sensitivity, high-definition sound quality.

For Pre AMP DAC Based on STUDER900. Output:Defult DC 5V with short circuit protection. STUDER line to the power line modeled output very high precision, low ripple, the actual sense of hearing is better than most Class A power.

AD828 Stereo Dynamic Microphone Preamplifier Module. 1pcs x AD828 Stereo Dynamic Microphone Preamplifier Board. MIC Preamp DC 3.7V-15V 12V. Notice: If you only used one channel, the other channel needs to short-circuit the input with GND, To avoid interference with the signal crosstalk.

Header DC resistance: 630 Ohm. The scale is precise, can be easily read the number. Weight: about 21 grams. Size:35 x 35mm(L W).

Model Number: WM-016.

Using original TAS5630, OPA1632DR, TL072. 1Pc x TAS5630 OPA1632DR TL072 600w /4ohm Class D Digital Subwoofer Amplifier Board. subwoofer frequency 2. Also note that monitor settings may vary from computer to computer and may distort actual colors.

1 AK4490EQ II2S DAC board. 1.6mm thick sheet using double-sided PCB, 2.0 oz copper thickness, HASL whole process to ensure that the size of the current through the good performance.

1pcs X LM386 module. components and total are widely used tape recorders and radios being. 4: The board default gain of 200;. 6: with power indicator light;. 3: Very few external components;.

Amplifier Chip: TPA3116 stereo, 50W 50W. 1 x Bluetooth Audio Receiver Amplifier. Amplifier Size: Approx. Audio source supports U disk / TF card decoding play and Bluetooth receiving play. Portable Audio & Headphones.

There are 8 green and 4 red leds for the chanel. It's a KIT - you will need soldering all parts together.

Using CSR8635 Bluetooth chip, Bluetooth V4.0, high software compatibility. 1PC 50W 50W TDA7492P Wireless Bluetooth 4.0 Digital Audio Receiver Amplifier Board. Output Power: Add pre-5532 output foot (powered 25V ,6-ohm impedance output 2 X 50W. ).

One pair CLONE PASS F5 TURBO Amplifier bare PCB. The price is for 2 channel Bare PCB. PCB size: 302 36. Copper Thickness: 35U.

This is Bare PCB, Not contains any other electric components. 1pcs x Bare PCB Board. And hope to see you soon. Working Current: 25A. Size: 97mm x 61mm.

Equipped with AUX interface. 1 Bluetooth 4.0 Audio Power Amplifier Board. Using CSR8635 Bluetooth chip, Bluetooth V4.0, high software compatibility. You can directly use it. Audio Input: Bluetooth Receiver V4.0.