HARDINGE 1-1/8" O.D. x 1/2" TOOL HOLDER BUSHING .500

tarsauto69
(2467)
Registered as a private seller
Consumer protection regulations resulting from EU consumer law are therefore not applicable. eBay buyer protection still applies to most purchases.
Seller's other items
Contact seller
US $18.99
ApproximatelyEUR 16.52
Condition:
Used
Postage:
US $5.25 (approx EUR 4.57) USPS Ground Advantage®.
Located in: Coloma, Wisconsin, United States
Delivery:
Estimated between Mon, 10 Nov and Fri, 14 Nov
Estimated delivery dates - opens in a new window or tab include seller's dispatch time, origin postcode, destination postcode and time of acceptance and will depend on delivery service selected and receipt of cleared paymentcleared payment - opens in a new window or tab. Delivery times may vary, especially during peak periods.
Returns:
No returns accepted.
Payments:
    Diners Club

Shop with confidence

eBay Money Back Guarantee
Get the item you ordered or your money back. Learn moreeBay Money Back Guarantee - opens new window or tab
Seller assumes all responsibility for this listing.
eBay item number:388628201700

Item specifics

Condition
Used: An item that has been previously used. The item may have some signs of cosmetic wear, but is ...
Brand
Hardinge
Tool Category
Lathe
Category

Item description from the seller

About this seller

tarsauto69

99.4% positive Feedback•10K items sold

Joined Aug 2006
Usually responds within 24 hours
Registered as a private sellerThereby, consumer rights stemming from EU consumer protection law do not apply. eBay buyer protection still applies to most purchases.
Visit shopContact

Detailed seller ratings

Average for the last 12 months
Accurate description
5.0
Reasonable postage cost
4.9
Delivery time
4.7
Communication
5.0

Popular categories from this shop

See allcategories
16c COLLETSGEOMETRIC CHASERS 9/16D HEADBT40 TOOLHOLDERSBRASS BAR STOCKS 20 COLLET PADS HARDINGEBT35 TOOL HOLDERSBT50 TOOL HOLDERSCAT 40 TOOL HOLDERSTHREAD PLUG GAGE

Seller Feedback (2,375)

All ratingsselected
Positive
Neutral
Negative
  • 1***0 (627)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    I don’t use a lot of brass so I don’t stock much brass. I had a small job to finish before leaving for vacation and item had been shipped 16 August arrived 2September several days after I left. I sourced the product and completed the job before leaving and I started a claim with eBay as shipper had obviously lost item. Received reply from vendor that he has had problems shipping stock in round shipping tubes. Simple solution is ship stock in square tubes. Anyway positive feedback.
    3/4" C360 BRASS ROUND ROD 12" long Solid .75" New Lathe Bar Stock H02 1/2 Hard (#388803023389)
  • 3***g (5475)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Excellent communication and even better customer service! Seller went out of his way to make sure thst my purchase was carefully packaged and promptly shipped. All in all, A HIGHLY RECOMMENDED SELLER! A+++!!!
    Vintage Jewelers Watchmakers Bench FOOT CONTROL FLYWEEL REAR SPEED PULLY& LATHE (#385757844872)
  • k***k (26)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Great seller ! Promptly shipped, packaged with care, accurately described
    1-1/8" I.D. x 1-1/2" O.D. x 3" LENGTH, SAE 660 CAST BRONZE BUSHING (#115348215617)
See all Feedback

More to explore: